Milwaukee 6391 Manuel d'utilisateur télécharger pdf (Page 7)

12 13

Fig. 13

Fig. 14

General Operation

Always clamp the workpiece securely on a

saw horse or bench (Fig. 13). See “APPLICA-

TIONS” for the correct way to support your

work in different situations.

1. Draw a cutting line. Place the front of the

shoe on the edge of the workpiece without

making blade contact. Hold the Tilt-Lok™

handle with one hand and the front handle

with the other (Fig. 14).

4. If making a partial cut, restarting in mid-

cut or correcting direction, allow the blade

to come to a complete stop. To resume

cutting, center the blade in the kerf, back

the saw away from cutting edge a few

inches, pull the trigger and re-enter the

cut slowly.

5. If the saw binds and stalls, maintain a ﬁ rm

grip and release the trigger immediately.

Hold the saw motionless in the workpiece

until the blade comes to a complete

stop.

6. After ﬁ nishing a cut, be sure the lower

guard closes and the blade comes to

a complete stop before setting the saw

down.

Troubleshooting

If the blade does not follow a straight line:

• Teeth are dull. This is caused by hitting a

hard object such as a nail or stone, dulling

teeth on one side. The blade tends to cut

to the side with the sharpest teeth.

• Shoe is out of line or bent

• Blade is bent

• Rip fence or guide is not being used

If the blade binds, smokes or turns blue

from friction:

• Blade is dull

• Blade is on backwards

• Blade is bent

• Blade is dirty

• Workpiece is not properly supported

• Incorrect blade is being used

2. Line up the sight line with your cutting

line. Position your arms and body to resist

KICKBACK. Pull the trigger, allowing the

motor to reach full speed before begin-

ning to cut.

3. While cutting, keep the shoe ﬂ at against

the workpiece and maintain a ﬁ rm grip. Do

not force the saw through the workpiece.

Forcing a saw can cause KICKBACK.

APPLICATIONS

Selecting Tilt-Lok™ Handle Positions

The Tilt-Lok™ handle is a feature which

allows the user to adjust the angle of the

handle for optimum cutting positions. The

Tilt-Lok™ handle has eight (8) detents

which allow the handle to snap into position

(Fig. 15). See “Adjusting Tilt-Lok™ Handle”

for instuctions on adjusting the handle. Re-

fer to the chart below for suggested handle

positions.

* These are only suggested positions; the actual optimum cutting position

may vary depending on the actual application and user preference.

APPLICATION SUGGESTED TILT-LOK POSITIONS*

For cuts made at or near

waist level

Handle in lower positions (Fig. 16) allows for more leverage

when pushing the saw through the workpiece.

For shallow cuts made at

or near waist level

Handle in lower positions allows the user to apply increased

downward force during shallow cuts.

For cuts made below the

waist, as in ﬂ ooring ap-

plications

Handle in higher positions (Fig. 17) reduce the amount of

“bending over” by the user. Higher handle positions allow

the user to apply an increased downward force on the saw.

For cuts made overhead,

as in ceiling applications

Handle in higher positions reduce the amount of extended

reach by the user for overhead cuts. Higher handle posi-

tions allow the user to apply an increased upward force on

the saw.

WARNING

To reduce the risk of injury, wear

safety goggles or glasses with side

shields. Unplug the tool before

changing accessories or making

adjustments.

Fig. 15

Fig. 16

Fig. 17

1 2 3 4 5 6 7 8 9 10 11 12 ... 26 27

Commentaires sur ces manuels

Pas de commentaire

Milwaukee 6391 Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Scies circulaires Milwaukee 6391