Milwaukee 9096-20 Manuel de l'opérateur télécharger pdf (Page 4)

ASSEMBLY

WARNING To reduce the risk of injury,

always unplug tool before changing or re-

moving accessories. Only use accessories

speciﬁ cally recommended for this tool. Others

may be hazardous.

Removing and Replacing Quik-Lok

Cords

(9072-20, 9072-22, 9092-20 and 9096-20)

Fig. 1

MILWAUKEE's exclusive Quik-Lok

Cords provide

instant ﬁ eld replacement or substitution.

1. To remove the Quik-Lok

Cord, turn the cord nut

1/4 turn to the left and pull it out.

2. To replace the Quik-Lok

Cord, align the connec-

tor keyways and push the connector in as far as

it will go. Turn the cord nut 1/4 turn to the right

to lock.

Attaching and Removing the Tool Hanger

(9092-20, 9096-20, or as accessory)

1.To attach, remove the two

top gear case screws.

2. Place the ring through

the tool hanger.

3. Position the tool hanger

on the tool over the two

gear case screw holes.

4. Replace the two gear

case screws. Hand

tighten the screws.

5. To remove, reverse the

procedure.

Fig. 2

Gear case

screws

WARNING Use only sockets and other

accessories speciﬁ cally designed for use on

impact wrenches and drivers. Other sockets

and accessories might shatter or break caus-

ing injury.

Attaching and Removing Accessories

(9071-20, 9075-20)

This impact wrench is intended only for use with

sockets designed for impact wrenches and that

have a 1/2" square drive (3/4" square drive for

Cat. No. 9075-20). Other sockets could shatter

or break, causing injury.

1. To attach a socket or other accessory, push the

accessory onto the drive shank until it snaps

into place.

2. To remove the accessory, pull it off the drive

shank.

Attaching and Removing Accessories

(9070-20, 9072-20, 9072-22)

These impact wrenches are intended only for use

with sockets designed for impact wrenches and

that have a 1/2" square drive. Other sockets could

shatter or break, causing injury.

1. To attach a socket or other ac-

cessory, align the hole in the

accessory with the detent pin

on the drive shank. Hold the

detent pin in while pushing the

socket onto the drive shank.

The detent pin will snap into

place in the hole to secure the

socket.

2. To remove the accessory, insert a nail or other

thin object into the hole in the accessory and

press the detent pin in. Pull the accessory off

the drive shank.

Attaching and Removing Accessories

(9092-20, 9096-20, or other Impact Wrenches using

the Quick Change 1/2" Square Drive to 7/16" Hex

Adapter)

Cat. No. 9092-20 and accessory Cat. No.

48-66-0061 are intended for use with accessories

with a 7/16" Hex Quick Change shank. Cat. No.

9096-20 is intended for use with accessories with

a 5/8" Hex Quick Change shank. Both Hex Quick

Change shanks have a ball-retainer groove. They

are not intended for use with Hex Shank Bit Ex-

tensions.

1. To attach an accessory, pull the chuck collar

forward and insert the accessory shank. Release

the collar. It may be necessary to pull the bit out

slightly to engage the holding mechanism.

2. To remove the accessory, pull the chuck collar

forward and remove the accessory. Release the

collar.

Starting, Stopping and Controlling Speed

(9072-20, 9072-22, 9092-20, and 9096-20)

This impact wrench may be operated at any speed

from 0 to full speed. The speed will remain variable

up to the chosen speed dial setting by use of the

trigger. The speed dial turns clockwise to increase

the speed or counterclockwise to decrease the

speed.

1. Select a speed on the

speed dial.

2. To start the tool, pull the

trigger.

3. To vary the driving speed,

increase or decrease pres-

sure on the trigger. The

further the trigger is pulled,

the greater the speed.

4. To stop the tool, release

the trigger.

Starting and Stopping the Tool

(9070-20, 9071-20, 9075-20)

These impact wrenches are equipped with a rocker

switch that offers both forward and reverse rotation.

1. For forward (clockwise) rota-

tion, pull the lower portion of

the switch.

2. For reverse (counterclock-

wise) rotation, pull the upper

portion of the switch.

NOTE: To prevent damage to

the motor and internal mecha-

nism, allow the motor to stop

completely before switching

from forward to reverse or from reverse to forward.

WARNING To reduce the risk of injury,

keep hands and cord away from the bit and

all moving parts.

WARNING To reduce the risk of explo-

sion, electric shock and property damage,

always check the work area for hidden pipes

and wires before drilling.

WARNING To

reduce the risk of injury,

only grasp tool by

handle and red insulated

surfaces. Do not hold

gray gear case when

impacting or drilling.

Fig. 6

Trigger

Speed

dial

To increase

the speed

Fig. 7

OPERATION

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

WARNING To reduce the risk of injury,

always unplug tool before attaching or remov-

ing accessories or making adjustments. Use

only speciﬁ cally recommended accessories.

Others may be hazardous.

Using the Forward/Reverse Switch

(9072-20, 9072-22, 9092-20, and 9096-20)

This impact wrench is equipped with a forward/

reverse switch that may be set to forward or re-

verse rotation.

1. For forward (clockwise) rotation, push the

forward/reverse switch in the direction shown.

Check the direction of rotation before use.

2. For reverse (counterclockwise) rotation, push

the forward/reverse switch in the direction shown.

Check the direction of rotation before use.

Fig. 4

Open (Release)

Closed (Locked)

Ball-retainer

groove

Fig. 5

Forward

Forward/Reverse Switch

Reverse

Fig. 3

Detent Pin

1 2 3 4 5 6 7 8 9 ... 12 13

Commentaires sur ces manuels

Pas de commentaire

Milwaukee 9096-20 Manuel de l'opérateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Clés à chocs Milwaukee 9096-20