135
Select one of these 4 MILWAUKEE motors for your No. 4202 or No. 4203 Electromagnetic Drill Stand.
These motors include reverse for compatibility with the Electromagnetic Drill Stand control panel.
4203 BASE ONLY
• ADJUSTABLE
POSITION,
• 11" DRILL
TRAVEL
4202 BASE ONLY
• FIXED POSITION,
• 9" DRILL TRAVEL
4253-1 4262-1 4292-1 4297-1
• 600 NO LOAD RPM • 350 NO LOAD RPM • TWO SPEED • TWO SPEED
• 750/375 • 500/250
NO LOAD RPM NO LOAD RPM
CHUCK CENTER DISTANCE FROM BASE
MOTOR NO. 4253-1
IN
OUT
Magnetic Stand 4202 1-1/4"
*
Plate Forward 4203 1-23/32"
*
Plate Back 4203 31/32"
*
MOTOR NO. 4262-1
IN
OUT
Magnetic Stand 4202 1-23/32" 4-11/16"
Plate Forward 4203 2-1/8" 5-3/32"
Plate Back 4203 1-3/8" 4-11/32"
MOTOR NO. 4292-1
IN
OUT
Magnetic Stand 4202 2-3/16" 4-3/8"
Plate Forward 4203 2-9/16" 4-11/16"
Plate Back 4203 1-13/16" 3-15/16"
MOTOR NO. 4297-1
IN
OUT
Magnetic Stand 4202 2-3/16" 4-3/8"
Plate Forward 4203 2-9/16" 4-11/16"
Plate Back 4203 1-13/16" 3-15/16"
IN = Closest to base OUT = Farthest away from base
*
Motor 4253-1 has only one chuck position.
Stand 4203 is adjustable 3/4" in direction of base length and
20° right or left.
All models furnished with 6 ft. safety chain.
■ Base Control Panel Includes Variable
Speed Adjusting For Motor
■ Solid State Electronic Switching
■ Feedback Speed Control
■ Computer Controlled Reverse
■ Full Wave Magnetic Holding Power
■ Forward/Reverse Control
■ Superior Cutting Tool Performance
■ Line Lock-Out
Prevents tool from operating should voltage
be restored to an interrupted line when
switch is locked in the "on" position.
■ Motor/Magnet Interlock
■ Automatic Base/Chip De-Mag
■ Automatic Electronic Soft Start
■ For Use On Any Flat Ferrous Material 1/2"
And Thicker
SPECIFICATIONS
*
DRILL REPLACEMENT REPLACEMENT
VOLTS NO POINT CHUCK CHUCK CHUCK KEY
CATALOG AC LOAD PRESSURE OR CATALOG CATALOG WEIGHT
NUMBER ONLY AMPS RPM DRILL ▲ TAP LBS. TAPER NUMBER NUMBER LBS.
4253-1 ● 120 6.2 600 1/2" 5/8"-18 † 1610/1650 Chuck 48-66-1360 48-66-3280 8.0
4262-1 120 11.5 350 3/4" 1"-14 1630/1670 Chuck 48-66-2085 48-66-3160 21.0
4292-1 120 11.5 750/375 1-1/4" 1"-14 1530/1600 No. 3MT 45-34-0110 #3 Taper Socket 23.0
4297-1 120 11.5 500/250 1-1/4" 1"-14 1530/1600 No. 3MT 45-34-0110 #3 Taper Socket 23.0
● Drills except No. 4253-1 have dual mount gear case permitting reverse mounting of drill for close quarter work.
†
5/8"-11 or 1/2"-13 taps not recommended.
▲ NOTE... To adapt a 3/4" capacity chuck to 1-1/4" Drills with No. 3 internal Morse Taper Socket specify Chuck and Arbor Kit No. 49-22-1550, which consists of Chuck No. 48-66-2000 and Arbor No.
48-07-0100. Extend chuck capacity to full drill capacity by using 1/2" reduced Shank Twist Drills shown in the MILWAUKEE catalog.
*
Drill point pressure on a 1" thick steel plate with the chuck mounted closest to the base. Values listed are for the drill motor mounted on a No. 4202 base/No. 4203 base that is adjusted to the rearward position.
CAT. WGT.
NO. HEIGHT WIDTH LENGTH LBS.
4202 15" 4-1/4" 11" 41.0
4203 17-1/4" 4-1/4" 11" 49.0
SPECIFICATIONS
DRILL STAND SPECS
CAPACITY
HEAVY-DUTY
ELECTROMAGNETIC DRILL
MOTORS AND BASES
(3 pages)
(21 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels