Milwaukee 48-10-5600 Manuel de l'opérateur télécharger pdf (Page 2)

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

WARNING READ ALL SAFETY WARNINGS AND INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or

serious injury. Save all warnings and instructions for future reference

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

POWER TOOL USE AND CARE

SERVICE

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

these devices can reduce dust-related hazards.

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc., in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the power

tool for operations different from those intended

could result in a hazardous situation.

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁ nger on the switch or energising power

tools that have the switch on invites accidents.

SPECIFIC SAFETY RULES

for vibration or wobbling that could indicate an

improperly installed bit.

• Maintain ﬁ rm grip on router when starting

motor to resist starting torque.

• Always keep the power supply cord away from

moving parts on the tool. Keep the cord away

from the direction of the cut.

• Never start the tool when the bit is in contact

with the material. The bit cutting edge may grab

the material causing loss of control of the tool.

• Never lay the tool down until the bit has come

to a complete stop. The spinning bit can grab

the surface and pull the tool out of your control.

• Never touch the bit during or immediately after

use. After use the bit may be hot enough to burn

bare skin.

• Use clamps or another practical way to secure

and support the workpiece to a stable plat-

form. Holding the work by hand or against your

body leaves it unstable and may lead to loss of

control.

• Never clamp the workpiece to a hard surface,

such as concrete or stone. Contact with the bit

could cause the tool to jump and loss of control.

• Only operate the routers when held. Do not

clamp or secure the router to a surface and hold

the workpiece by hand.

• Never use bits larger than the smallest of the

openings in the base, sub-base, or dust collection

port.

• Do not loosen or remove the

plunge base caps. Internal

springs are under pressure.

If loosened or removed, the

plunge base caps and internal

springs will become projectiles,

which could cause injury.

Double Insulated

Plunge Base Caps

• Hold power tools by insulated gripping sur-

faces when performing an operation where

the cutting tool may contact hidden wiring or

its own cord. Contact with a “live” wire will make

exposed metal parts of the tool “live” and shock

the operator.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• Always wear safety goggles and dust mask.

Use only in a well ventilated area. Using per-

sonal safety devices and in a safe environment

reduce the risk for injury.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

speciﬁ cally designed to ﬁ lter out microscopic

particles.

• Some woods contain preservatives that can be

toxic. Take extra care to prevent inhalation and

skin contact when working with these materials.

Request, and follow, any safety information avail-

able from your material supplier.

• Always make sure the workpiece is free from

nails, screws and other foreign objects. Keep

the working edge away from the clamping

surface. Cutting these objects can cause loss

of control of the tool and damage to the bit.

• Never hold the workpiece in one hand and

the tool in the other hand when using the

tool. Never place hands near or below cutting

surface. Clamping the material and guiding the

tool with both hands is safer.

• Never use dull or damaged bits. Sharp bits

must be handled with care. Damaged bits can

break during use. Dull bits require more force to

push the tool, which could cause the bit to break.

Damaged bits can throw carbide pieces and burn

the workpiece.

• After changing the bit or making any adjust-

ments, make sure the collet nut and any

other adjustment devices are securely tight-

ened. Loose adjustment devices can unexpect-

edly shift, causing loss of control. Loose rotating

components will be violently thrown. Watch

Symbology

Volts Alternating Current

No Load Revolutions per

Minute (RPM)

Amperes

Underwriters Laboratories, Inc.,

United States and Canada

1 2 3 4 5 6 7 ... 20 21

Commentaires sur ces manuels

Pas de commentaire

Milwaukee 48-10-5600 Manuel de l'opérateur Page 2

Commentaires sur ces manuels