Milwaukee 48-59-1801 Manuel d'utilisateur télécharger pdf

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 WEST LISBON ROAD • BROOKFIELD, WISCONSIN 53005 USA

(262) 781-3600

TO: AUTHORIZED portable electric tool SERVICE STATIONS DATE: January 2008

factory SERVICE / SALES SUPPORT BRANCH

TOOL(S) \ PRODUCT(S) AFFECTED: 2601-20 18.0V Li-Ion Compact Driver/Drill

48-11-1815 18.0V 1.4Ahr Li-Ion Battery Pack, 48-59-1801 18.0V Charger

SUBJECT: Troubleshooting Guide 48-59-1801 18.0V Charger / 48-11-1815 18.0V Li-Ion Battery Pack

Symptom

Possible Cause(s) Solution(s)

Battery Pack

connected to

Charger, RED

or GREEN

LED lights

failure to turn

“on”.

Line voltage too high or too

low (or no power present)

Charger temperature too high

>212ºF

(100ºC)

Faulty Battery Pack – ‘blown’

FET

Faulty Charger

Remove Battery Pack. Unplug Charger and verify correct line voltage -

90VAC – 132VAC for 120VAC Charger

Allow Charger to cool 3-5 minutes before attempting charge. Power must be

removed for a minimum of one minute then reapplied if this condition occurs.

Try known good Battery Pack on the questionable Charger, or try questionable

Battery Pack on known good Charger. FET can fail when battery pack is

repeatedly over-loaded - under extreme circumstances, the internal

temperature of the battery becomes too high or subjected to water.

UNPLUG Charger - high voltage is present at the AC High Voltage Heat Sink -

when AC line voltage is applied to the Charger circuit board. Check for ‘blown’

Charger DC low voltage ‘one-time’ output protection fuse F2 with Volt-Ohm

Meter and/or ‘blown’ Charger AC line fuse - F1, if fuse F2 checks OK. NOTE:

Before checking fuses F1 or F2 unplug the Charger from power source and let

it sit for 3-4 minutes before disassembling – this allows circuit board capacitor

to self discharge.

Use only a battery operated VOM to perform FUSE continuity test – it may be

necessary to pierce / scrap the protective coating of PCB board on end of fuse

to obtain valid continuity reading.

48-59-1801 Charger has no serviceable replacement

parts.

O INFORM YOU

PRODUCT

SUPPORT

BULLETIN # 474

AC HIGH VOLTAGE HEAT SINK

DC HEAT SINK SIDE

FUSE

1 2

O INFORM YOU 1

Résumé du contenu

Page 1 - O INFORM YOU

MILWAUKEE ELECTRIC TOOL CORPORATION 13135 WEST LISBON ROAD • BROOKFIELD, WISCONSIN 53005 USA (262) 781-3600 TO: AUTHORIZED portable e

Page 2

Symptom Possible Cause(s) Solution(s) Battery Pack fuel gauge LEDs fail to progress from 1 to 2 to 3 to 4 LED lit first LED only, stays blinking

Plus de documents pour Chargeurs de batterie Milwaukee 48-59-1801

Voir le document Milwaukee 48-59-1801 Manuel d'utilisateur

Milwaukee 48-59-1801 Manuel d'utilisateur (11 pages)

Commentaires sur ces manuels

Pas de commentaire

Milwaukee 48-59-1801 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chargeurs de batterie Milwaukee 48-59-1801. TO INFORM YOU - Milwaukee Tool Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Chargeurs de batterie Milwaukee 48-59-1801

Commentaires sur ces manuels

Produits connexes et manuels pour Chargeurs de batterie Milwaukee 48-59-1801